Our solutions
Industrial condensate treatment solutions range
Industrial condensate treatment solutions range
Industrial condensate treatment solutions range
Industrial condensate treatment solutions range
Industrial condensate treatment solutions range
Process gas and air equipment
Industrial Tools & Solutions
Industries Served
Industrial Tools & Solutions
Industries Served
Industries Served
Industries Served
Industrial Tools & Solutions
Vacuum solutions

Applicable Standards and Regulations in the Compressor Industry

Compressed Air Wiki Basic Theory

In the compressed air sector, as in many other industrial sectors, regulations apply. They may include requirements that are defined by legislation as well as optional regulations or recommendations, as for national and international standards.

Industry standards

standards and regulations

Sometimes regulations in standards may become binding when they come into force through legislation. If a standard is quoted in a commercial agreement it can thereby also be made binding. Binding regulations can apply, for example, to safety for people and property while optional stan-dards are used to facilitate work with specifications, selection of quality, performing and reporting measurements, manufacturing drawings etc.

The benefits of international standardization are obvious to both manufacturers, intermediate parties such as engineering companies and final customers. It increases the interchangeability of products and systems, and allows performance statements to be compared on equal terms. These performance statements may include operational, environmental and safety aspects.

Standards are referred to frequently by legislators as a way of creating uniform market impacts. Standards may be produced, issued and maintained by standardization organizations on national, supranational (European) and international levels, but equally by specific trade associations focusing on specific industrial sectors (the petroleum industry, compressed air industry, electronics industry etc).

Standards produced by the International Organization for Standardization (ISO) may be converted into national standards by the ISO member countries at their discretion. Standards produced by the CEN (European Committee for Standardization), are developed for use by the 30 national members, and conversion into national standard may be mandatory in the case of harmonized standards.

All standards can be acquired through the various national standardization organizations.
In the compressed air industry, standards may also be produced by trade associations such as PNEUROP (European committee of manufacturers of compressed air equipment, vacuum pumps, pneumatic tools and allied equipment), or its counterpart CAGI (United States Compressed Air and Gas Institute). Examples of such documents are the performance measurement standards for compressor capacity, oil content in the compressed air, etc. which were issued while awaiting an international standard to be developed.


A non-exhaustive list of current (2010) standards within the compressed air industry follows below. The listed references are both European and US. Pneurop standard initiatives are usually issued in parallel with a CAGI issue for the American market. It is recommended to check with the issuing body to ensure that the latest edition is being used, unless the particular market requirement/demand refers to a dated issue.

Machinery safety

EU Machinery directive 2006/42/EC, referring to the following standards:

Pressure equipment safety

EU Directive 87/404/EC, Simple pressure vessels

EU  Directive  97/23/EC,  Pressure  Equipment, referring to the following standards:


EU Directive 2000/14/EC, Outdoor Noise Emission, referring to the following standards:

Electrical safety

EU Directive 2004/108/EC, Electromagnetic compatibility, referring to the following standards:

EU Directive 2006/95/EC, Low Voltage Equipment, referring to following standards:

Medical devices-general

EU Directive 93/42/EC, referring to the following standards:


ISO 3857-1:1977, Compressors, pneumatic tools and machines - Vocabulary - Part 1: General

ISO 3857-2:1977, Compressors, pneumatic tools and machines - Vocabulary - Part 2: Compressors

ISO 5390:1977, Compressors - Classification

Specifications and testing

ISO 1217:2009, Displacement compressors – Acceptance tests

ISO 5389:2005, Turbo-compressors - Performance test code

ISO 7183:2007, Compressed air dryers - Specifications and testing

ISO 12500:2007-Part 1 to 3, Filters for Compressed Air – Test Methods

ISO 8573-Part 1 to 9, Compressed Air - Contaminants and purity classes – Test Methods


Related articles

What is Compressed Air?

Compressed air is all around us, but what is it exactly? Let us introduce you to the world of compressed air and the basic workings of a compressor.