Drying Compressed Air: The Aftercooler
Learn more about the different ways we can treat compressed air and the different tools that are used in these processes. Here we talk about drying compressed air and aftercoolers.
Search the Compressed Air Wiki
Why is it Important to Dry Compressed Air?
All atmospheric air contains some amount of water vapor. Now, consider the atmosphere as a giant, slightly wet, spunge. If we squeese that spunge very hard, the water absorbed will drip out. The same happens when air is compressed, which means the water concentration will increase. To avoid future problems in the compressed air system, the wet air needs to be treated. This takes place using an aftercooler and drying equipment.
Why and how do we dry compressed air?
Atmospheric air contains more water vapor at high temperatures and less at lower temperatures. This has an effect on the water concentration when the air is compressed. For example, a compressor with a working pressure of 7 bar and a capacity of 200 l/s that compresses air at 20˚C with a relative humidity of 80% will release 10 liters/hour of water in the compressed air line. Problems and disturbances can occur due to water precipitation in the pipes and connected equipment. To avoid this, the compressed air must be dried.
What is pressure dew point?
The term "pressure dew point" (PDP) is used to describe the water content in the compressed air. It is the temperature at which water vapor condenses into water at the current working pressure. Low PDP values indicate small amounts of water vapor in the compressed air.
It is important to remember that atmospheric dew point can not be compared with PDP when comparing different dryers. For example, a PDP of +2˚C at 7 bar is equivalent to –23˚C at atmospheric pressure. To use a filter to remove moisture (lower the dew point) does not work. This is because further cooling leads to continued precipitation of condensation water.
You can select the main type of drying equipment based on the pressure dew point. When taking cost into account, the lower the dew point required, the higher the investment and operating costs for air drying. Five techniques exist for removing the moisture from compressed air: cooling plus separation, over-compression, membranes, absorption and adsorption drying.
Different drying methods
There are a number of ways to dry compressed air, most of them are listed below. For more on how to choose the right dryer for your application, click here. - Aftercoolers - Refrigerant dryers - Over compression - Absorption and Adsorption Drying (Descidant dryers) - Membrane dryers
How to dispose of the condensate after drying the air?
Anyone who runs a compressed air system (using oil-injected technology) needs to be aware of how to properly dispose of the condensate in a responsible manner, so as not to infringe any environmental laws. The condensate released by compressed air equipment will have tiny particles of oil in that are not visible to the naked eye, which is why it needs proper disposal. Not only is incorrect disposal detrimental to the environment, but you could also incur a fine and damage to your reputation as a responsible company.
There are many rules concerning the disposal of waste generally, as you will no doubt be aware if you have paid a recent visit to your local recycling centre and compared that to a visit only a few years ago. Don’t let your compressed air supply catch you out without doing a fairly easy first check.
Have a walk around your compressed air equipment: you should be able to see the condensate drains appearing from the back of the compressors and dryers on your site. Take a look at where these are piped to. Ideally you should see them all going to an oil/water separator of some description and then off to a foul drain. If they are going straight from a drain onto the floor or just into a standard plastic container then this should raise a red flag. Oil/water separators are very easy to install. Note that there are many rules around the disposal of condensate, even with the correct equipment in place, and the rules can vary from region to region.
Related articles
How to Remove Contaminants from Compressed Air?
A number of decisions must be made when installing a compressed air system for it to provide the right air quality. Let us take a look at how to remove harmful contaminants, like water vapor and oil, from the output air.
The Quality of Compressed Air
A number of decisions must be made when installing a compressed air system for it to suit different needs and provide the right air quality.